Control of Molecular Motion by Metal-Plated 3D-Printed Plastic Pieces
April 28, 2017 | EPFLEstimated reading time: 3 minutes
EPFL scientists have combined 3D-printing with electroplating to easily produce high-quality metal electrodes that can be used as a molecular beam-splitter.
Many measurement techniques, such as spectroscopy, benefit from the ability to split a single beam of light into two in order to measure changes in one of them. The crucial device that separates the beam is the beam-splitter. These have been mostly limited to light beams, where one uses simply a partially reflective glass. EPFL scientists have now developed a similar device for splitting beams of molecules, where high-voltage electrodes are used to control the motion of the molecules inside a vacuum. The electrodes are built by an innovative method that combines 3D printing and electroplating for the fabrication of complex metallic structures. The same approach can also be used in a wide range of other experiments. The new method is published in Physical Review Applied and overcomes previous fabrication problems thus opening up new avenues.
Sean Gordon and Andreas Osterwalder at EPFL’s Institute of Chemical Sciences and Engineering, developed the new fabrication method, and demonstrated it by constructing the complicated combination of electrodes required to guide and split beams of molecules. The production method not only allows complex shapes to be made but, in addition, speeds up production by a factor of 50-100.
The technique begins by 3D-printing a plastic piece and then electroplating a 10 μm-thick metal layer onto it. Electroplating is an established technique in various branches of industry like the automobile industry, fabrication of jewelry, or plumbing. It generally uses electrolysis to coat a conductive material with a metallic layer. “but the plating of printed pieces has not been done before in the context of scientific applications,” says Andreas Osterwalder.
To make the printed plastic pieces conductive and thus amenable to electroplating, they were first pre-treated by a special procedure developed by the company Galvotec near Zurich. Once the first conductive layer was applied, the pieces could be treated as if they were metallic. The first step can be applied selectively to certain regions of the printed piece, so that the final device contains some areas that are metallic and conductive while others remain insulating.
This process enabled the researchers to build two electrically independent high-voltage electrodes from a single printed plastic piece and with the correct geometry for beam-splitting. Meanwhile, the procedure allows an almost free choice of the coating metal, including some that would be very hard to machine.
This approach also produced surfaces that have no scratches, recesses or abrasions. The molecular beam-splitter used to prove the new method is a structure based on very complex electrodes that require impeccable surface properties and high-precision alignment. “All of which comes for free when using the 3D-printing approach,” says Andreas Osterwalder.
Along with cost, the new 3D printing/electroplating method also drastically reduces production time: Traditional manufacturing for such structures can often take several months. But in the EPFL study, all the components were printed within 48 hours and electroplating only took a day. The shorter time allows for very fast turnover and more flexibility in the development and testing of new components.
Finally, 3D printing uses an entirely digital workflow — the electrodes are printed directly from a computer and require no manual input. This means that an exact replica of a complete experimental setup can be reproduced anywhere by simply transferring a computer file.
The new fabrication method highlights the enormous potential that 3D printers have for fundamental research, in a variety of research areas. It especially demonstrates that we can now quickly produce chemically robust electrically conductive pieces with high precision and at low cost since 3D printing is virtually unlimited in terms of design and the geometry of structures.
Suggested Items
IDTechEx Discusses the Role of Printed Sensors in Mass-Digitization
04/11/2024 | PRNewswireIntegrated sensors digitizing physical interactions are vital in everyday life. From personalized user experiences to warehouse inventory management, data-driven insights are driving demand for smarter sensors — and lots of them.
A Closer Look at Professional Development at IPC APEX EXPO 2024: 3D Printing and AI
04/09/2024 | I-Connect007 Editorial TeamWhile the finishing touches were being made to the show floor at IPC APEX EXPO, just as much activity was happening in the conference rooms of the Anaheim Convention Center on the days before the show officially opened. The hallways and classrooms were filled for standards committee development meetings and Professional Development Courses, and IPC hosted evening receptions for Emerging Engineers, ECWC, and those who are attending for the first time in a special “newcomers” event.
Mycronic to Showcase More Versatile, High-productivity Assembly Solutions at IPC APEX EXPO 2024
03/27/2024 | MycronicMycronic, the leading Sweden-based electronics assembly solutions provider, will continue to respond to growing customer demand for high-flexibility, high-productivity solutions for zero-defect PCB assembly at IPC APEX EXPO 2024 in Anaheim, CA on April 9 - 11.
DARPA Explores Additive Manufacturing’s Revolutionary Potential for Futuristic Microsystems
03/12/2024 | DARPADARPA played a seminal role in establishing materials science as a discipline. One of the latest disruptive efforts in new materials and applications, the Additive Manufacturing of Microelectronic systEms (AMME) program, seeks to launch microsystems manufacturing far beyond today’s state of the art.
StenTech to Unveil Cutting-Edge StenTech BluPrint™ CVD Surface Treatment at 2024 IPC APEX EXPO
03/12/2024 | StenTechStenTech® Inc., a leading global company specializing in SMT Printing Solutions, will introduce the new StenTech BluPrint™ Chemical Vapor Deposited (CVD) Surface Treatment at the 2024 IPC APEX EXPO.