Electronics and Optics on One Chip Getting Light out of Silicon
November 13, 2017 | University of TwenteEstimated reading time: 2 minutes
Electronics and light don't go well together on a standard 'CMOS' chip. Researcher Satadal Dutta of the University of Twente succeeded in introducing a light connection into the heart of a semiconductor chip. In this way, two circuits can communicate. Or: the worlds of electronics and photonics are connected.
What is particularly attractive about Dutta's solution is that no special materials or manufacturing processes are needed: the light comes from silicon. The light source, detector and the light channel can be made using the technology that is used to make the electronic circuits. Fully optical circuits are available nowadays, but they use materials like indium phosphide and gallium arsenide, which can't easily be combined with the CMOS chip processes used for semiconductor chips you'll find in today's smartphones, for example.
Avalanche LED
The alternative would be: make a LED out of silicon. And that's the problem: silicon only emits a tiny amount of infrared light, while a detector made out of silicon needs visible light. They are talking and listening at different wavelengths. Dutta therefore chooses a remarkable way out: connect the LED reverse. At low voltages, there's no current, but at a voltage that is high enough, there will be a small current that amplifies itself like an avalanche. In this 'avalanche mode', the LED will transmit visible light. Using the same process, the light detector, as well as the light channel in-between can be made. Thanks to the special comb structure that Dutta designed, the light source gets more uniform and energy efficient.
Isolation
An optical link on a chip is a good way to 'galvanically' isolate two circuits from each other. This is often necessary in cases where one circuit is a low-voltage and low-current one, while the other is a high-power circuit. They should be connected, but not by conducting wires, for reasons of safety. A classic transformer is an option then, but an optical connection is often used as well. Until now, this is a separate 'optocoupler', which is large and has a limited bit rate. Dutta's new solution is much more compact as an alternative: it total, it is just a few tens of microns and it offers the protection that's needed. Compared to optical channels in full-optical circuits, the energy consumption is relatively high, as there is quite some scattering of light. On the other hand: designing the electronics around the optical link in an efficient way, the amount of light needed for a successful connection, can be kept to a minimum.
Connecting worlds
All-optical circuits may become the 'new electronics', predictions say. In the transition from electronic to optic circuits, hybrid circuits, like the one Dutta designed, could play an important role.
Satadal Dutta (1990, Barrackpore, India) did his PhD research in the Semiconductor Components group of Prof Jurriaan Schmitz, together with the Integrated Circuit Design group of Prof. Bram Nauta. Dutta defended his thesis 'Avalanche-mode silicon LEDs for monolithic optical coupling in CMOS technology' on 8 November. It was supported financially by NWO-TTW in The Netherlands and by NXP Semiconductors.
Suggested Items
IMI Taps New Opportunities to Sustain Grit in China
03/28/2024 | IMIIntegrated Micro-Electronics, Inc. (IMI), Joey S. Bantatua, IMI China’s head of operations and general manager was recently interviewed by Asia Electronics Industry (AEI) magazine where he talked about the prospects of the country both as a market and a production hub.
Kimball Electronics Publishes Annual Sustainability Disclosures with its 2023 Guiding Principles Report
03/28/2024 | BUSINESS WIREKimball Electronics, Inc. published its annual sustainability disclosures in its 2023 Guiding Principles Report, themed “How We Are Winning Together The Kimball Way.”
iNEMI Webinar: Humidity Robustness and Insulation Coordination for e-Mobility
03/27/2024 | iNEMIThis webinar is a follow-up to the recent Seminar on Humidity Robustness and Insulation Coordination for e-Mobility, organized by iNEMI and ZESTRON Europe and supported by the ECPE.
Electronics Industry Sentiment Rises in March
03/27/2024 | IPCIPC releases March 2024 Global Sentiment of the Electronics Supply Chain Report
Mycronic to Showcase More Versatile, High-productivity Assembly Solutions at IPC APEX EXPO 2024
03/27/2024 | MycronicMycronic, the leading Sweden-based electronics assembly solutions provider, will continue to respond to growing customer demand for high-flexibility, high-productivity solutions for zero-defect PCB assembly at IPC APEX EXPO 2024 in Anaheim, CA on April 9 - 11.