New IC Manufacturing Lines to Boost Total Industry Wafer Capacity 8%
February 9, 2018 | IC InsightsEstimated reading time: 1 minute
IC industry wafer capacity, specifically in the memory segment, was inadequate to meet demand throughout 2017. However, with Samsung, SK Hynix, Micron, Intel, Toshiba/WD, and XMC/Yangtze River Storage Technology planning to significantly ramp up 3D NAND flash capacity over the next few years, and Samsung and SK Hynix boosting DRAM capacity this year and next, what does this mean for total industry capacity growth? In its 2018-2022 Global Wafer Capacity report, IC Insights shows that new manufacturing lines are expected to boost industry capacity 8% in both 2018 and 2019 (Figure 1). From 2017-2022, annual growth in IC industry capacity is forecast to average 6.0% compared to 4.8% average growth from 2012-2017.
Figure 1
Large swings in the addition or contraction of wafer capacity by the industry, as a whole, appear to be moderating. Since 2010, annual changes in wafer capacity volume have been in the relatively narrow range of 2-8%, with the largest year-to-year difference being just three percentage points. This suggests that IC manufacturers are better today than in years past about trying to match supply with demand. It’s still an incredibly difficult task for companies to gauge how much capacity will be needed to meet demand from customers, especially given the time it takes a company to move from the decision to build a new fab to that fab being ready for mass production.
Many companies, DRAM and NAND flash suppliers in particular, have become much more active with new fab construction and expansion projects at existing fabs. This surge in activity comes after four years (2014-2017) when capacity growth lagged wafer start volume increases. During the past few years, IC producers have worked to increase utilization rates from the low levels in 2012-2013.
Figure 2
If all the new fab capacity expected to be brought on-line in 2019 happens as planned, the volume of capacity added that year will approach the record set in 2007. Figure 2 shows more that 18 million wafers per year of new capacity is expected to be added in 2019, and this number even assumes some of the massive DRAM and NAND fabs being built by Chinese companies will not be carried out quite as aggressively as has been advertised. IC Insights believes that construction of these China-owned fabs is progressing slower than planned.
Suggested Items
The New Chapter: Attracting ‘Generation Green’
03/28/2024 | Hannah Grace & Paige Fiet -- Column: The New ChapterIn the electronics industry, we talk a lot about sustainability in terms of recruitment and retention of the next generation of engineers. But what if the key to sustaining the industry long into the future is through the more common definition of the word? What if, for just a moment, we think about sustainability in terms of the environment and what we as an industry are doing to care for it? Because, if you weren’t aware, Gen Z cares tremendously about the environment and the actions companies are taking to preserve it. Without Gen Z joining the electronics industry’s workforce, we won’t be able to sustain the industry for much longer.
Accenture Invests in Sanctuary AI to Bring AI-Powered, Humanoid Robotics to Work Alongside Humans
03/27/2024 | BUSINESS WIREAccenture has made a strategic investment, through Accenture Ventures, in Sanctuary AI, a developer of humanoid general-purpose robots that are powered by AI and can perform a wide variety of work tasks quickly, safely and effectively.
Don Dennison Appointed to Roll Out KIC’s Latest Thermal Analysis System Software in the Northeast
03/26/2024 | KICKIC, a renowned pioneer in thermal process and temperature measurement solutions for electronics manufacturing, is pleased to announce the appointment of PIT Equipment Services, LLC, led by Don Dennison, as its representative for New York, New Jersey, and Eastern Pennsylvania.
iNEMI/IPC White Paper on Complex Integrated Systems Highlights Future Technology and Manufacturing Ecosystem Needs
03/25/2024 | IPCToday’s system solutions combine more varied functionality, such as digital, analog, optical, micro-mechanical, etc., packed into smaller form factors. As a result, electronics manufacturing has to deliver increasingly complex integration of diverse technologies with system designs that blur the distinction between chip, package, board, and assembly.
Seeking Employment: Meet Gary Turner
03/25/2024 | Barry Matties, I-Connect007Meet Gary Turner, a recent graduate from the University of Texas at Dallas with a bachelor’s degree in mechanical engineering and a master’s in material science and engineering. He is currently seeking employment in the industry. The following interview will allow you to learn about Gary and see if he might be a good candidate for a position you are looking to fill.