Nickel Ferrite Promotes Capacity and Cycle Stability of Lithium-Sulfur Battery
June 12, 2018 | Science China PressEstimated reading time: 1 minute
Lithium-sulfur (Li-S) battery can be put into practice, if 20% of theoretical energy densities (2600 Wh/kg or 2800 Wh/L) can be achieved. Investigators have the ambition to reach the energy density of 500 Wh/kg in the near future.
Xue-Ping Gao and co-workers, from Nankai University, tell us "Till now, the volumetric energy density of 500 Wh/L is not satisfied. But it was already realized in commercial lithium-ion batteries (LIBs) many years ago." They emphasize, "The low volumetric energy density is a bottleneck of practical Li-S battery."
Intrinsically, sulfur has lower density than transition metal oxides as cathode in LIBs. Worse, in order to improve the electrochemical performance, sulfur is usually forced to load onto various light-weight carbon hosts, leading to more lower volumetric capacity of sulfur-based composites, and undermining the volumetric energy density of Li-S battery.
Compared with various carbon materials, heavy metal oxides not only offer good adsorption ability of polysulfides to suppress the shuttle effect, but also help to obtain dense sulfur-based composites with high tap density, which could be the primary reason for realizing both the good stability and high volumetric capacities of sulfur-based composites.
Gao introduces, "Based on above consideration, we developed nickel ferrite (NiFe2O4) porous hollow 1D nanofibers via electrospinning technology. The as-prepared NiFe2O4 nanofibers were used here as a novel host of sulfur in order to increase the volumetric capacity of sulfur-based composites."
Gao details their experiment, "Firstly, the polysulfide adsorption test reveals the strong chemisorption towards soluble polysulfides by NiFe2O4." Both the stable adsorption geometry and adsorption energy of Li2S8 on (111) plane of NiFe2O4 are confirmed by Density Functional Theory (DFT) calculation as compared with carbon nanotubes (CNTs).
As a result, the S/NiFe2O4 composite delivers an initial discharge capacity of 963.6 mAh/g, and good cycle stability. "Furthermore," he said, "the S/NiFe2O4 composite shows nearly 2 times higher superior volumetric capacity than S/CNT composite."
Gao points out, "It comes no surprise that the S/NiFe2O4 composite has much larger the tap density than the S/CNT composite."
In addition, other metal ferrites MFe2O4 (M = Co, Mg, Zn) have also been investigated as polar host of sulfur, and the results confirm the superiority of metal ferrites in fabricating sulfur-based composites with high gravimetric/volumetric capacities for the potential application of Li-S batteries with high gravimetric/volumetric energy density.
Suggested Items
Water Management in a Large Printed Circuit Board Manufacturer
04/15/2024 | Charles Nehrig, TTM TechnologiesTTM’s environmental management is grounded in its Environmental Statement and Environmental Policy, which promote measures that make for a more responsible environmental management process. Our management system helps TTM work toward minimizing its environmental footprint and increasing the sustainability of its operations. TTM monitors its environmental performance just as it monitors its operational performance, and provides the resources required to adhere to the Company’s environmental responsibilities.
Happy’s Tech Talk #27: Integrated Mesh Power System (IMPS) for PCBs
04/08/2024 | Happy Holden -- Column: Happy’s Tech TalkA significant decrease in HDI substrate production cost can be achieved by reducing the number of substrate layers from conventional through-hole multilayers and microvia multilayers of eight, 10, 12, and more to only two layers. Besides reducing direct processing steps, the yield will increase as defect-producing operations are eliminated. The integrated mesh power system (IMPS) was invented in the latter years of MCM-D use for thin-film fabrication. Those geometries fit today into our use of ultra HDI.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
Indium Corporation Experts to Present at SEMI THERM
03/07/2024 | Indium CorporationIndium Corporation Global Account Manager and Senior Thermal Technologist Tim Jensen and Product Development Specialist for Thermal Interface Materials Miloš Lazić will present on thermal interface material (TIM) technology at SEMI-THERM, taking place March 25–28 in San Jose, California, U.S.
Indium Corporation to Showcase Proven EV Products and High-Reliability Alloys at Productronica China
02/28/2024 | Indium CorporationAs a materials pioneer and trusted partner in electric vehicle (EV) and e-Mobility manufacturing, Indium Corporation is proud to showcase its high-reliability alloys and soldering solutions at Productronica China, March 20-22, in Shanghai.