Novel Process for Structuring Quantum Materials
August 1, 2019 | Forschungszentrum JülichEstimated reading time: 2 minutes
Implementing quantum materials in computer chips provides access to fundamentally new technologies. In order to build powerful and fault-resistant quantum computers, it is possible, for example, to combine topological insulators with superconductors. This process step brings with it some challenges that have now been solved by researchers from Jülich.
Image Caption: a) Scanning electron micrograph during the "Jülich process": A chip can be seen during fabrication. The topological insulator (dyed red) has already been selectively deposited. In a next fabrication step, the superconductor is applied via shadow mask deposition. In black-and-white, various mask systems are recognizable which make it possible to manufacture the desired components completely in ultrahigh vacuum. b) In such networks one wants to try to move so-called majorana modes (represented as stars) along the topological tracks in order to enable topologically protected quantum computing operations. While the blue and violet Majorana fashion stays in the same position (x, y) in the room. Credit: Forschungszentrum Jülich / Peter Schüffelgen
Even the ancient Inca used knots in cords to encode and store information in their ancient writing "Quipu". The advantage: unlike ink on a sheet of paper, the information stored in the knot is robust against external destructive influences, such as water. Even novel quantum computers should be able to store information robustly in the form of nodes. For this, however, no cord is knotted, but so-called quasi-particles in space and time.
What is needed to build such a quantum node machine are new materials called quantum materials. Experts speak of topological insulators and superconductors. The processing of these materials to components for quantum computers is a challenge in itself; especially because topological insulators are very sensitive to air.
Scientists in Jülich have now developed a novel process that makes it possible to structure quantum materials without exposing them to air during processing. The so-called "Jülich process" makes it possible to combine superconductors and topological insulators in ultrahigh vacuum to produce complex components.
Initial measurements in their samples indicate evidence of majorana states. "Majoranas" are exactly the promising quasiparticles to be knotted in the shown networks of topological insulators and superconductors to enable robust quantum computing. In a next step, the researchers of the Peter Grünberg Institute, together with their colleagues from Aachen, the Netherlands and China, will provide their networks with readout and control electronics in order to make the quantum materials available for the application.
Suggested Items
Material Insight: The Dielectric Constant of PCB Materials
05/17/2024 | Dr. Preeya Kuray -- Column: Material InsightIn the world of PCB design, miniaturization can be achieved by using low dielectric constant (Dk) materials. Low Dk materials can allow for a reduction in thickness while maintaining a given trace width, leading to lower transmission loss and higher density circuitry.
IPC APEX EXPO: Some Thoughts About Growth
05/16/2024 | Dan Feinberg, I-Connect007After two and a half days of wandering the aisles at IPC APEX EXPO 2024, for the first time, I almost felt like I was exploring CES. There were so many booths and exhibits that I could describe, but I’d like to focus on the growth and huge value of this event, which has expanded well beyond just the growing and impressive exhibit show floor.
The Shaughnessy Report: Unlock Your High-speed Material Constraints
05/15/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportThe world of PCB materials used to be a fairly simple one. It was divided into two groups: the “traditional” laminates, often called FR-4, and the high-speed laminates developed especially for high-speed PCBs. These were two worlds that usually didn’t collide. But then traditional laminates started getting better, and high-speed designers and design engineers took notice and started to reconsider what FR-4 could be used for.
Breaking High-speed Material Constraints: Design007 Magazine — May 2024
05/14/2024 | I-Connect007 Editorial TeamDo you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems instead of high-speed materials, saving time and money while streamlining the fab process. In the May 2024 issue of Design007 Magazine, our contributors explain how to avoid overconstraining your materials when working with high-speed boards.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.