Photovoltaic-Powered Sensors for the “Internet of Things”
September 27, 2019 | MITEstimated reading time: 5 minutes
By 2025, experts estimate the number of “internet of things” devices — including sensors that gather real-time data about infrastructure and the environment — could rise to 75 billion worldwide. As it stands, however, those sensors require batteries that must be replaced frequently, which can be problematic for long-term monitoring.
MIT researchers have designed photovoltaic-powered sensors that could potentially transmit data for years before they need to be replaced. To do so, they mounted thin-film perovskite cells — known for their potential low cost, flexibility, and relative ease of fabrication — as energy-harvesters on inexpensive radio-frequency identification (RFID) tags.
The cells could power the sensors in both bright sunlight and dimmer indoor conditions. Moreover, the team found the solar power actually gives the sensors a major power boost that enables greater data-transmission distances and the ability to integrate multiple sensors onto a single RFID tag.
“In the future, there could be billions of sensors all around us. With that scale, you’ll need a lot of batteries that you’ll have to recharge constantly. But what if you could self-power them using the ambient light? You could deploy them and forget them for months or years at a time,” says Sai Nithin Kantareddy, a PhD student in the MIT Auto-ID Laboratory. “This work is basically building enhanced RFID tags using energy harvesters for a range of applications.”
In a pair of papers published in the journals Advanced Functional Materials and IEEE Sensors, MIT Auto-ID Laboratory and MIT Photovoltaics Research Laboratory researchers describe using the sensors to continuously monitor indoor and outdoor temperatures over several days. The sensors transmitted data continuously at distances five times greater than traditional RFID tags — with no batteries required. Longer data-transmission ranges mean, among other things, that one reader can be used to collect data from multiple sensors simultaneously.
Depending on certain factors in their environment, such as moisture and heat, the sensors can be left inside or outside for months or, potentially, years at a time before they degrade enough to require replacement. That can be valuable for any application requiring long-term sensing, indoors and outdoors, including tracking cargo in supply chains, monitoring soil, and monitoring the energy used by equipment in buildings and homes.
Joining Kantareddy on the papers are: Department of Mechanical Engineering (MechE) postdoc Ian Matthews, researcher Shijing Sun, chemical engineering student Mariya Layurova, researcher Janak Thapa, researcher Ian Marius Peters, and Georgia Tech Professor Juan-Pablo Correa-Baena, who are all members of the Photovoltaics Research Laboratory; Rahul Bhattacharyya, a researcher in the AutoID Lab; Tonio Buonassisi, a professor in MechE; and Sanjay E. Sarma, the Fred Fort Flowers and Daniel Fort Flowers Professor of Mechanical Engineering.
Combining Two Low-Cost Technologies
In recent attempts to create self-powered sensors, other researchers have used solar cells as energy sources for internet of things (IoT) devices. But those are basically shrunken-down versions of traditional solar cells — not perovskite. The traditional cells can be efficient, long-lasting, and powerful under certain conditions “but are really infeasible for ubiquitous IoT sensors,” Kantareddy says.
Traditional solar cells, for instance, are bulky and expensive to manufacture, plus they are inflexible and cannot be made transparent, which can be useful for temperature-monitoring sensors placed on windows and car windshields. They’re also really only designed to efficiently harvest energy from powerful sunlight, not low indoor light.
Perovskite cells, on the other hand, can be printed using easy roll-to-roll manufacturing techniques for a few cents each; made thin, flexible, and transparent; and tuned to harvest energy from any kind of indoor and outdoor lighting.
The idea, then, was combining a low-cost power source with low-cost RFID tags, which are battery-free stickers used to monitor billions of products worldwide. The stickers are equipped with tiny, ultra-high-frequency antennas that each cost around three to five cents to make.
RFID tags rely on a communication technique called “backscatter,” that transmits data by reflecting modulated wireless signals off the tag and back to a reader. A wireless device called a reader — basically similar to a Wi-Fi router — pings the tag, which powers up and backscatters a unique signal containing information about the product it’s stuck to.
Traditionally, the tags harvest a little of the radio-frequency energy sent by the reader to power up a little chip inside that stores data, and uses the remaining energy to modulate the returning signal. But that amounts to only a few microwatts of power, which limits their communication range to less than a meter.
The researchers’ sensor consists of an RFID tag built on a plastic substrate. Directly connected to an integrated circuit on the tag is an array of perovskite solar cells. As with traditional systems, a reader sweeps the room, and each tag responds. But instead of using energy from the reader, it draws harvested energy from the perovskite cell to power up its circuit and send data by backscattering RF signals.
Page 1 of 2
Suggested Items
Real Time with… IPC APEX EXPO 2024: Automation in North American PCB Shops
05/17/2024 | Real Time with...IPC APEX EXPOBenmayor Group has entered the North American market's automation landscape with their Technosystem division. In this interview, Eduardo Benmayor highlights this underinvestment and current efforts to catch up and address challenges related to strategic planning. Eduardo shares Technosystem's automation journey, from simple equipment to robotic arms, stressing the importance of machine communication and data analysis. He also offers advice on implementing automation in older facilities.
Using AI to Redefine Productivity
05/15/2024 | Nolan Johnson, SMT007 MagazinePlato Systems, a machine perception company spun out of Stanford University, employs AI and video data to analyze and optimize the human component in manufacturing. Initially focused on semiconductors, Plato Systems has expanded into EMS manufacturing. Co-founder and CEO Amin Arbabian, along with product advisor Anders Holden and head of growth Luis Vidal, discuss their approach to changeover optimization and its impact on productivity in the industry. They’ve also included customer Raj Vora in the conversation.
Real Time with… IPC APEX EXPO 2024: Manufacturing Intelligence from the Factory Floor
05/15/2024 | Real Time with...IPC APEX EXPONolan Johnson and Ranjan Chatterjee, Vice President of Smart Factory Business Units at PDF Solutions, discuss the background of Cimetrix and PDF Solutions. They explore the analytics tools provided by PDF Solutions, the merging of semiconductor and electronics manufacturing, and data handling in these industries. They also discuss different product lines, standards, packaging technologies, data usage, and integration with ERP systems
Nolan’s Notes: Coming to Terms With AI
05/07/2024 | Nolan Johnson -- Column: Nolan's NotesHow fast do things move in the world of data analytics? Here’s an example. We’ve been planning this issue on artificial intelligence for the past few months, and, in fact, I had already written this column about a month ago. Then I went to IPC APEX EXPO and upended it all. I originally had compared AI to drag racing in that (CPU) horsepower and new (data) vehicles have steadily delivered higher performance competition. That seemed pretty accurate given how generative AI models dominated the popular media with amazing results—and sometimes spectacular crashes.
RTX's Advanced Ground System for Space-based Missile Warning Now Operational
05/06/2024 | RTXAn advanced ground system for space-based missile warning developed by Raytheon, an RTX business, is now operational at the U.S. Space Force's Overhead Persistent Infrared Battlespace Awareness Center (OBAC).