Weak Material Prices Prevailed Throughout 2015
December 23, 2015 | IHSEstimated reading time: 2 minutes
Current construction costs fell again in December, according to IHS Inc. and the Procurement Executives Group (PEG). The headline current IHS PEG Engineering and Construction Cost Index (ECCI)registered 41.8 this month, down from 43.7 in November. Despite the slight ups and downs, the headline index remained consistently below the neutral mark in 2015, indicating that costs have declined throughout the year. In addition, December's index figure marked the lowest reading for 2015.
The current materials/equipment price index slowed to 37.8, down from 40.5 in November, the lowest level since the survey began four years ago. All underlying material and equipment components showed falling prices except ready-mix concrete, which showed neutral prices. Copper-based wire and cable registered the highest drop compared to last month, moving from 42.5 in November to 27.5 in December. Transformers, fabricated structural steel and exchangers price indexes also retreated relative to November.
“The latest data for the PEG indexes highlight the general softness in the pricing environment and, more particularly, the filtering through of the sharp and continuing drop in commodity prices that began back in the summer of 2014, said John Mothersole, director of research at IHS Pricing and Purchasing. “While declines in certain material categories, such as wire and cable, stand out at the moment, the pervasive weakness in the data hints at a broad weakness in aggregate demand.
The current subcontractor labor index remained unchanged in December at 51.1. The sub index recorded its lowest level ever in October, and since has remained just above neutral. In the United States, most geographies reported neutral price movements for subcontractor labor, with the exception of US Northeast, where prices increased with an index reading of 55.0. In both Eastern and Western Canada, subcontractor labor hit the neutral mark.
The six-month headline expectations index eased to 50.1 in December, reverting back to a weak but positive outlook. The materials/equipment index fell to 48.9, from 50.6 in November. Only one third of the materials and equipment categories came in above the neutral mark, with ready-mix concrete registering the highest price expectations. For future subcontractor labor costs, expectations remained above the neutral mark at 52.9. Subcontractor labor cost expectations fell in Western United States and Eastern Canada. They strengthened in Western Canada and the majority of the US, with the US South posting the highest price expectations.
2015 in Review
The headline IHS PEG Engineering and Construction Cost Index (ECCI) finished the year on a weak note, reflecting the deteriorating price environment of 2015. In 2014, steel-related products such as alloy steel pipe and fabricated structural steel recorded widespread price increases. This year the price indexes for the same materials as well as carbon steel pipe showed 12 months of falling prices. The weak price environment has also been widespread, with materials such as transformers, electrical equipment and copper-based wire and cable registering at least nine months of falling prices. Lower Chinese demand for commodities and reduced investment from the oil and gas industry throughout 2015 have kept the cost environment weak. Ready-mix concrete was the only material that recorded real pricing strength during the year, tied mainly to strong demand in the Southern US and tight supplies of cement throughout the country.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.